I have created a composing chart using recharts as attached here :
this issue is if I add a label on Y-axis that contains more than 8 letters it either goes to the next line or out of the container, I wrote a workaround where I just show the acronyms on the Y-axis and then the description in the tooltip but the requirement is to show the complete name in the label on Y-axis, so is there any way we can move the Y-axis on the right-hand side so that we can allot more space to the label?
I tried adding a domain to X-axis which did not help much
Related
I would like to add nested axis Labels to my radar chart. All online resources just show a singular axis.
An example of the image I am trying to reproduce is shown in the below figure.
The axis is Management.sr_lvl_1, Management.sr_lvl_2, Management.sr_lvl_3... However, I want the word management to appear only once in the label which spans across all sr_lvl
I am trying to plot a line graph on Bokeh and i am using 2nd y axis to the right side as well. For this reason i put y_axis_location to None. But when i am trying to change the start and the end option from Range1 does it only to the yaxis not in my main figure. The problem is that i want my application to plot as initial graph this that can be displayed after i zoom out as the 2nd picture above (after zoom out) but what i get is the 1st picture instead.
By the way i found what cause this error, it has to do with y_range_name which need to take the name of the y_range that you named at the starting point.
I have a page with 3 different charts. I'd like to make them look good. Here's what it looks like:
http://i.stack.imgur.com/JY0Yl.jpg
As you can see there are several problems with the formatting here.
How do I make the Y-axis labels align? In this case, they're right aligned, and the graph starts at the right. So, since the labels are different, each of the graphs starts in a different column.
How do i remove the first and last or the X-axis labels? In this case, two things happen. In one side, the label overlaps the Y-label, and on the other side, the label wraps around and uses two lines.
How do I space the graphs? Each graph is its own DIV container, and it's jqPlot that decides to format it, and overrides my DIV formatting.
For point 3 you may be able to place each div inside an additional div that you will be able to format with CSS as you want. And if it work you may reuse your hide X axis solution with a better result.
I have tried using all sorts of combinations of tickInterval, tickPixelInterval label formatter and tickPositioner and I haven't been able to solve this issue.
I have a chart builder that pulls in different feeds and allows the user to modify the date range of those feeds before shooting this data into highcharts and spitting out the chart.
The problem is that some of the time, the first and/or last dates get cut off. Here is an example:
Without adjusting the margins of the chart (which causes the chart to take up less space), how do I prevent this from happening?
If I was able to determine the pixel location of the ticks and their labels, I could in theory, hide the specific ticks and their corresponding labels which were located outside the graph / cut off. Thoughts?
Without looking at your code - there are a few things you can do.
Rotate your labels
Play around with the x/y axis labels
Align them to the right
Hopefully one of these would help your cause.
Hi i wonder if it's possible to disable the automatic scaling of a highchart.
Or is ist possible to set a fixed position and or width and height to the labels ?
Here is an example, this is how i'd like to have my chart look like.
http://jsfiddle.net/ynXgw/6/
But if the labels have a different length highchart shrinks the graph.
http://jsfiddle.net/ynXgw/7/
Has anybody an idea how i could fix this?
One way to solve your problem is to use a different series to display the labels. In this example I use a second scatter series to display the labels. To position the labels just set the y value. I set the color of the points to the same color as the background to hide them. Then I use the dataLabels formatter to display the labels how you want them.